Instrumentation Strength - Erection and Commissioning
-
Commissioning, & Trouble shooting of Solenoid valves by operating the solenoid coil and observing the correct change over action.
-
Commissioning, Trouble shooting and calibration of control valves by rising and falling signals at 0,25,50,75 and 100% of valve stroke
-
Commissioning and calibration of pneumatic positioner, I/P Converter, Electro Pneumatic positioner, position feedback transmitters and Smart Positioners.
-
Installation, Commissioning, and calibration of motorized valves by setting open/close Limit Switches and Torque Switches for Fully closed and Opened Position.
Pre – Commissioning activities – Checking for design conformity & functional check
-
Inspection of equipment and installation to check for mechanical integrity
-
Inspection of equipment and installation to check for compliance with drawings, specifications, regulations and code of practice Simulator
-
Connecting the Handheld Programmer and Running communication test
-
Powering up the transmitters until stabilized
-
Zero and Ranging the Transmitters by use of HART/MFM Handheld Communicator as per Data sheet
-
Checking the outputs in both raising and falling modes
-
Checking up Cold and Hot Loop checking for the control loops
Supervision and Support services for Erection, Commissioning, Site acceptance test as of following Jobs
-
Installation of all type of field instruments as per P&I Drawings
-
Glanding and cable Termination in Instruments, junction Boxes & Marshalling Panels for DCS or PLC system
-
Continuity checking for Control and Signal cables.
-
Installation of stanchions/Supports and Canopy for instruments
-
Process loop checking of field Instrument
-
Impulse tubing for instruments as per Hook up Drawings
-
Copper S.S Tubing for all types of control valves/ON-OFF Valves
-
Laying & clamping of single pair/ Multicore cables up to control room
-
Stroke checking for control valves & Partial stroke for ESD Valves
-
Laying of perforated/Ladder type cable tray and fixing the cable tray bends according to the cable route
DCS, PLC & SCADA System Commissioning Activities
-
Ensuring Dual Power Supply Change over without affecting the system/Process
-
Checking of Nest Loading as per the I/O allocation
for maintaining the redundancy -
Confirm of all inter-connector cables have been installed in accordance with the reference documents.
-
Check of all I/O cabling to field devices and the field devices are installed and comply with the reference documents
-
Uploading and Downloading the program, Logic design, nest loading and I/O assignment, graphic design and implementation for SIEMES S7300 & 400and its WinCC, ABB 800XA, AC 900F, Yokogawa Cs3000 & Centum VP, Annunciator and SOE
-
Checking System Architecture according to the approved drawings.
Our Esteemed
Services
Our Electrical Strength in the field
-
Electrical equipments Testing & Commissioning
-
Electrical Erection Supervision
-
Manpower assistance and supervision
-
Control & Relay panel wiring, Numerical Relay testing & configuration
-
Harmonics measurement, capacitance & tan delta measurement, specialized testing for generators
-
Instrument & Meter Calibration
-
Cable laying and termination both electrical and instrumentation
Electrical Division
-
To carry out Erection & supervision of electrical equipment in power plant, Substations, Process Plants, Cement Industry and Oil and Gas Sector .
-
To carry out Normal Testing & Commissioning Activities for Substation, Power Plants, Process Plants, Infra structure Projects etc., in India.
-
To carry out the special testing activities like Tan delta & Capacitance testing, Sweep Frequency Response Analysis (SFRA), Thermo vision Camera to Measure & Monitor the temperature in different Electrical contacts, Dynamic Contact Resistance Measurement for HV Circuit Breakers, Power Quality Analysis-Harmonic Analysis; Online Meter Calibration; SF6 Gas Dew point Measurement, Vibration Measurement, Noise level measurement, Oil Bath Kit for Transformer Temp. Indicators Calibration activities,
-
To carry out the Testing and Commissioning of all kind advanced Numerical Protection Relays such as Distance Protection, Transformer Protection, Generator Protection, Bus bar Protection and all kind of Relays – Configuration to Commissioning.
-
To carry out the periodical maintenance activities for all kind of electrical equipments for power plant, Process plants, Substations Etc.,
-
To carry out the Regular Operation & Maintenance activities for power plants, Substations Etc.,
-
To carry out Transformer servicing including, over all inspection and servicing, gasket changing, oil filtration and oil testing, oil leakage arresting etc.,
-
To provide manpower support for various activities like erection supervision, cable termination and glanding, isolator alignment etc. with various category from un skilled man power to skilled and qualified engineers.
-
To provide competitive and skilled services for the International Clients by deputing relevant engineers as per the requirement of the customers from the above Divisions and also to execute the Testing & Commissioning in a Proficient manner to the Utmost Satisfaction of the end user.